Functional Description (FUB) Valvetronic relay

Functional description Valvetronic relay Valvetronic relay The Valvetronic relay is used for the power supply for the output stage in the engine control unit. The output stage activates the Valvetronic servomotor. Note! The correct installation location for the Valvetronic relay can be called up via the hotspot on the diagnosis wiring diagram! Functional description ...

Functional Description (FUB) Compressor relay

Functional description Compressor relay Compressor relay The air supply system of the single-axle air suspension is activated via the compressor relay. The compressor relay is located ... for the electronic ride height control (EHC) activates the compressor relay. The self-levelling suspension works by feeding or extracting air into or out of the air springs of the rear axle ...

Functional Description (FUB) Relay and relay 2 for rear-window drive

Functional description Relay and relay 2 for rear-window drive Relay and relay 2 for rear-window drive The convertible top module (CVM) will activate the corresponding relay to open or close the rear window. Relay for rear-window drive: To Open the rear window the convertible top module will activate the relay for the rear-window drive. Relay 2 for rear-window drive ...

Functional Description (FUB) Cut-off relay

Functional description Cut-off relay Cut-off relay The cut-off relay, auxiliary battery and starter motor generator are components of the starter unit. The starter unit enables ... generator delivers high charge current to the auxiliary battery at high engine speeds. To avoid overcharging the auxiliary battery, the cut-off relay must be closed when a certain engine ...

Functional Description (FUB) Cut-off relay

Functional description Cut-off relay Cut-off relay On some types of vehicle with certain combinations of engine and gearbox (weight on the front axle), a more powerful ... is fitted for the power supply (24 Volts) of this power steering. By means of a cut-off relay, this auxiliary battery is switched into series with the vehicle battery. The EPS control ...

Functional Description (FUB) Coolant pump relay

Functional description Coolant pump relay Coolant pump relay The coolant pump is integrated in the cooling circuit (low temperature) and is used for the charge air cooling ... values, are realised. The coolant pump relay supplies the coolant pump for the charge air cooler with voltage via terminal 30 (supply voltage). Note! The correct installation location ...

Functional Description (FUB) Relay, terminal 30B

Functional description Relay, terminal 30B Relay, terminal 30B The Car Access System (CAS) is the master control unit for the terminal control. The CAS control unit activates the wake ... . The terminal 30B relay is installed in the junction box. Note! The correct installation location for the terminal 30B relay can be called up via the hotspot on the diagnosis wiring diagram ...

Functional Description (FUB) Relay, terminal 30B

Functional description Relay, terminal 30B Relay, terminal 30B The Car Access System (CAS) is the master control unit for the terminal control. The CAS control unit activates the wake ... . The terminal 30B relay is installed in the rear fuse carrier. Note! The correct installation location for the terminal 30B relay can be called up via the hotspot on the diagnosis wiring ...

Functional Description (FUB) DDE main relay

Functional description DDE main relay DDE main relay The DDE control unit (DDE stands for "Digital Diesel Electronics") is supplied with voltage via the DDE main relay. Functional description Following enable by the Car Access System (CAS) or the front electronic module (FEM), terminal 30B connects with the excitation coil. The DDE main relay picks up ...

Functional Description (FUB) Front fuse and relay module

Functional description Front fuse and relay module Front fuse and relay module Due to the steady increase in the number of electrical functions in the areas of comfort, communication ... the fuses, a number of relays are also plugged into or soldered onto the printed circuit board. If one of the soldered relays is faulty, the complete front power distribution box must ...

Functional Description (FUB) Cutoff relay, electric fan

Functional description Cutoff relay, electric fan Cutoff relay, electric fan The engine control system activates the electric fan. The power supply from terminal 30 is connected by the engine control system via the cutoff relay of the electric fan. Note! Depending on the equipment specification of the electric fan, one of the following cutoff relays are installed ...

Functional Description (FUB) Rear window wiper relay

Functional description Rear window wiper relay Rear window wiper relay The rear wiper is driven by the wiper motor (direct current motor) and switched on via the rear window wiper relay. The relay is fitted in the power distribution box in the junction box. Note! The correct installation location for the rear window wiper relay can be called up via the hotspot ...

Functional Description (FUB) Relay, quantity control valves

Functional description Relay, quantity control valves Relay, quantity control valves The relay supplies the quantity control valves with terminal 15N. Note! The correct installation location for the quantity control valve relay can be called up via the hotspot on the wiring diagram in the diagnosis system! Functional description At the excitation coil in the quantity ...

Functional Description (FUB) Front fuse and relay module

Functional description Front fuse and relay module Front fuse and relay module Due to the steady increase in the number of electrical functions in the areas of comfort, communication ... the fuses, a number of relays are also plugged into or soldered onto the printed circuit board. Functional description The fuses are directly connected to the front power distribution ...

Functional Description (FUB) Secondary air pump relay

Functional description Secondary air pump relay Secondary air pump relay The electric secondary air pump is switched on by the secondary air pump relay. Note! The installation location of the secondary air pump relay is dependent on the series: The correct installation location can be called up via the hotspot on the wiring diagram! The purpose of the secondary air ...

Wiring Diagram (SSP) Front fuse and relay module

Front fuse and relay module SP0000056901 11114 Front fuse and relay module Z1 JBE F62 F26 F23 F25 F31 F19 F4 F12 F13 F64 F34 F2 F67 F11 F10 F54 F27 F66 F52 F32 F63 F33 F65 F35 F29 F28 F43 F44 F45 F5 F46 F42 F22 F21 F20 F47 F55 F16 F3 F58 F73 F72 F71 F74 F60 F61 F15 F14 F8 F9 F7 F37 F51 F24 F50 F36 F18 F17 F38 F56 F53 F75 F39 F40 F1 F48 F57 F59 F41 JBE Kl. 30F A51 X6 ...

Functional Description (FUB) Voltage supply and DDE main relay

Functional description Voltage supply and DDE main relay Voltage supply and DDE main relay     Function The voltage supply of the DDE control unit is effected in the following steps when the ignition is switched on: When the ignition is switched on, voltage is applied to the DDE control unit via terminal 15WUP and terminal 15_3. The DDE main relay is switched via ...

Functional Description (FUB) Load-shedding relay for ignition and fuel injection system

Functional description Load-shedding relay for ignition and fuel injection system Load-shedding relay for ignition and fuel injection system Terminal 87 provides the load-shedding relay for ignition and injection to the connected control units and components. Note! The correct installation location for the load-shedding relay for ignition and injection can be called ...

Functional Description (FUB) Load-shedding relay for ignition and fuel injection system

Functional description Load-shedding relay for ignition and fuel injection system Load-shedding relay for ignition and fuel injection system Terminal 87 provides the load-shedding relay for ignition and injection to the connected control units and components. Note! The correct installation location for the load-shedding relay for ignition and injection can be called ...

Repair Instructions (REP) Replace heat exchanger

... : Heating and air-conditioning unit removed for purposes of clarity. Unclip the relay lever (1) from the angle positioning lever (2). Installation note: Relay lever (1) must engage audibly ...

Repair Instructions (REP) Information on intelligent battery sensor (IBS)

61 12 ... Information on intelligent battery sensor (IBS) Notice! Do not connect the charger to the 12 V charging socket The 12 V charging socket is supplied with voltage by the rear power distribution box via relay. This relay drops out after terminal 15 OFF. This means that a trickle charger connected at the 12 V charging socket will be disconnected from ...

Repair Instructions (REP) Replacing actuator drive for recirculated air flap

...  (1). Unclip the relay lever (2) using a suitable tool. Remove actuator drive (3). Unlock plug connection (4) and disconnect. Replacement: Servomotors must be readdressed in the event ...

Repair Instructions (REP) Replacing the air supply system

37 22 540 Replacing the air supply system Important! When replacing the air supply system it is imperative that the relay for the air supply system is replaced at the same time. Important! Danger of injury! Drain the air suspension system before carrying out any work on the air supply system, air pipes and air spring struts! Danger of injury if this instruction ...

Repair Instructions (REP) Instructions for removal and replacement of control units

... should only ever be connected and disconnected while the ignition is turned off. The removal and installation of components, relays, fuses etc. can cause faults to be stored in fault ...

Functional Description (FUB) Power distribution box, rear

... the fuses, a number of relays are also plugged into or soldered onto the printed circuit board. If one of the soldered relays is faulty, the complete rear power distribution box must be replaced. Depending on the series and vehicle equipment, various relays are mounted on the printed circuit boards in the rear power distribution box. The fuse assignment also depends ...

Functional Description (FUB) Power distribution box

... include the following: Valvetronic Ignition and fuel injection Electric coolant pump The power distribution box contains fuses and relays. If one of the fuses or one of the relays is faulty ... distribution box are protected with fuses. Terminal 30 is connected to each output. The engine control unit (DME) is supplied with voltage via the DME main relay from terminal 15N ...

Functional Description (FUB) Junction Box Electronics

... supplied with power from the JBE control unit. Power distribution box The fuses and various plug-in and soldered relays are located in the junction box power distribution box. Depending on the vehicle equipment, the printed circuit boards of the power distribution box are fitted with different relays. There is an opening in the lower part of the junction box ...

Functional Description (FUB) Soft top drive

... Main pillar hydraulic cylinder 2 Fin hydraulic cylinder 3 Soft top compartment lid hydraulic cylinder 4 Soft top drive 5 2 relays for activation of the electric motor with hydraulic pump ... to CLOSED) is controlled by 2 relays. The cylinders are supplied with hydraulic fluid by a hydraulic pump (3 pistons) with 2 directions of rotation. The direction of movement is determined ...

Functional Description (FUB) Voltage supply Integral Active Steering (SA 2VH)
Applies to: P2VH (Integral Active Steering) 2012/07+

Description of operation Voltage supply Integral Active Steering (SA 2VH) Auxiliary battery, charging controller for auxiliary battery and cut-off relay With several vehicle types ... which requires a supply voltage of 24 volts. An auxiliary battery is installed for the voltage supply of this EPS; it can be switched using a cut-off relay in series with the main ...

Functional Description (FUB) Starter motor

... voltage through to the starter motor relay via terminal 50L. The starter pinion is engaged in the ring gear of the flywheel using the starter relay and the intermediate gearbox or planetary ... unit activate the starter motor relay via terminal 50L. The starter relay is a combination of a relay and an solenoid. The starter relay has the following tasks: Starter pinion ...

Functional Description (FUB) Junction Box Electronics

... request. This request is read out by the electronics in the wiper motor and the respective wiper stage is initiated. For the headlight cleaning system, a separate relay is installed ... . The connections optimise the wiring harness. Here the junction box electronics functions as a nodal point. The junction box electronics (JBE) have internal and external relays. The excitation ...

Functional Description (FUB) Power distribution box, engine compartment

... ;). If a high-power electric fan (e.g. 850 or 1000 watt) is installed, then an electric fan relay is installed in the electric line between the battery power distribution box and the engine compartment power distribution box. The engine control unit activates the electric fan relay. If a low-power electric fan (e.g. 400 or 600 watt) is installed, then an electric fan ...

Functional Description (FUB) Vehicle system voltage supply

...  V (connection to the cut-off relay and auxiliary battery), starter unit (hybrid car). DC/DC converter (400 W) for support during engine start (vehicle with automatic engine start-stop ... compartment on the right. In addition to the fuses, a number of relays are also plugged into or soldered onto the printed circuit board. If one of the soldered relays is faulty ...

Functional Description (FUB) DC/DC converter

... the terminal 30B DC/DC relay with constant voltage, also during the starting operation. The relay is located in the DC/DC converter. 2 further relays in the DC/DC converter switch ... earth Terminal 15N Terminal 15, power supply for after-run Terminal 50 Terminal 50, starting operation SIG Diagnosis lead Terminal 30B Close relay, terminal 30B Terminal 30F Close relay ...

Functional Description (FUB) Subwoofer fanfare and tweeter fanfare

... to the signal evaluation, the junction box electronics (JBE) now takes over the relay activation for the fanfares. For the following examples, the following applies: The steering column ... . According to the signal evaluation, the Body Domain Controller (BDC) takes over the relay activation for the fanfares. Example F25: The horn switch is directly connected to the steering column ...

Functional Description (FUB) Fuse box 2

... distribution box terminal 30 are protected with fuses. One line leads to the cut-off relay. The other line leads to the Electrical Machine Electronics (EME). Index Explanation Index Explanation 1 Fuse box 2 2 Connection for battery cable to the cut-off relay 3 Fuse 4 Fuse 5 Connection for positive battery lead from the auxiliary battery. 6 Connection for battery cable ...

Functional Description (FUB) Transmission oil pump

... is activated by a relay. The transmission oil pump relay is in the engine compartment power distribution box. The engine control activates the transmission oil pump relay. In addition ... connection. The transmission oil pump relay is supplied with terminal 15B via the power distribution box in the junction box. The ground connection is connected at the engine. Index ...

Functional Description (FUB) CAS/FEM/BDC enable line

Functional description CAS/FEM/BDC enable line The function of the CAS/FEM/BDC enable line is to relay the engine start "enabled" status from the DDE to the CAS/FEM/BDC ... runs a check on the status conditions as soon as the vehicle is unlocked and then relays the engine start "enabled" status to the CAS/FEM/BDC. If the Start button ...

Functional Description (FUB) Charging controller for auxiliary battery

... Steering (AL) and a defined combination of engine and transmission (weight on front axle): Voltage supply with 24 V via auxiliary battery, cut-off relay and charging controller ... Activation of the cut-off relay Monitoring of the cable shield Index Explanation Index Explanation 1 Charging controller for auxiliary battery 2 Holder 3 six-pin plug connection 4 4-pin ...

Functional Description (FUB) Subwoofer fanfare and tweeter fanfare

... reinforces the sound of the diaphragm. Due to their high power requirement, fanfares are switched on via a relay, the fanfare horn relay. The following graphic shows the fanfares ... , the junction box electronics (JBE) activates the fanfare horn relay. ZGM: Central gateway module Depending on the series, the central gateway module (ZGM) is either a separate control unit ...

Functional Description (FUB) Secondary air pump

... description The engine control activates the secondary air pump relay. The secondary air pump relay switches on the secondary air pump shortly after the engine starts. The switch-on period ... air pump is activated by the engine control via the secondary air pump relay. The secondary air pump receives its power supply from the engine electrical system fuse carrier (terminal 30 ...

Functional Description (FUB) Rear-window drive

... . The rear window is opened and closed by reversing the motor's direction of rotation. The direction of movement of the rear window (opening or closing) is controlled by 2 relays. The relays are installed near the rear power distribution box. The convertible top module (CVM) controls the relays. An incremental sensor and a separate hall effect sensor are installed ...

Functional Description (FUB) Electric fuel pump

... pump is activated via either an electronic fuel pump control module (EKPS) or a fuel pump relay. If the vehicle is fitted with the electronic fuel pump control system, the electric ... in the fuel pump control module (EKPS). The characteristic curves are coded for the specific motor and model. If the electric fuel pump is activated via the fuel pump relay, the engine control ...

Functional Description (FUB) Wiper drive

... Domain Controller (BDC) switches the 2 wiper stages using a relay activation as follows: Wiper stage 1: Relay not activated Wiper stage 2: Relay activated The end position (also called ... ) switches the 2 wiper stages for the windscreen wiper using relay activation. The reset contact is connected to the front electronic module (FEM) or the Body Domain Controller (BDC) via ...

Functional Description (FUB) Electric motor for rear wiper

... on the K-CAN2 to the Rear Electronic Module (REM). The junction box electronics or the Rear Electronic Module or the Body Domain Controller evaluates the signal. The wiper relay is activated in accordance with the evaluation. The wiper relay is installed in the power distribution box in the junction box or in the Rear Electronic Module or in the Body Domain Controller ...

Wiring Diagram (SSP) Fuse F502

... engine K2085 DDE main relay X2085 6 K6341 Load shedding relay for ignitionand fuel injection X6341 6 K6341 Load shedding relay for ignitionand fuel injection X6341 6 RT 4.0 30<502 K6300 Load-shedding relay for ignitionand fuel injection system K6300*1B 6 K6316 Variable valve gear relay K6316*1B 6 N52/N63TU engine Z11 Integrated supply module X60189 N53 engine N20 engine ...

Functional Description (FUB) Power distribution box

... the power distribution box with terminal 15N. Terminal 87. The fuse box on the vehicle battery supplies the load-shedding relay for ignition and injection. Then, terminal 87 of the Digital Motor Electronics (DME) will be supplied by the load-shedding relay for ignition and injection.   Item Explanation Item Explanation 1 Power distribution box 2 4 Fuses Structure ...

Functional Description (FUB) Electric fan

... supply from terminal 30 via a relay comes from the engine control system. Depending on the equipment specification, this electric fan cutoff relay is at different installation locations ... Explanation Terminal 31L Load ground Terminal 87 Battery voltage terminal 30 via radiator fan cutoff relay PWM Pulse-width modulated signal Characteristic curve and setpoint values ...

Wiring Diagram (SSP) Terminal control

... 2 3 Z2*1B 5 2 A16*1B 1 10 Z2*1B 7 35 A34*1B 40 23 A34*3B 41 11 A16*2B 24 BR 2.5 31 2 3 30 30 30 30F 15N 30B Z2_1 Z2 Fuse holder, rear1)Relay, terminal 30B2)Relay, terminal 15N3)Bistable relay 31 31 31 31 Z1 Junction box2)Relay, terminal 15N3)Bistable relay4)Relay, terminal 30B A34 30 30F 3 2 30 30 15N 30B Z1_4 Z1*1B 1 S25*1B 1 S25 Brake light switch RT/BL 0.5 30B_1 ...

Functional Description (FUB) Digital diesel electronics

... characteristic maps. The DDE control unit activates the actuators directly or via relays. The control unit is woken up via the wake-up line (terminal 15 wake-up line) by the Car Access System ... unit is supplied with terminal 30 by the rear distribution box via the DDE main relay. The CAS control unit or the FEM control unit activates the DDE main relay. Item Explanation Item ...

Functional Description (FUB) Fanfare button

... . The steering column switch cluster relays the command signal to the FlexRay in the form of a message. The central gateway module (ZGM) is on the FlexRay bus. The Central Gateway Module links ... to reception of a command signal by activating the air horn relay. The air horns are available for operation at all switch positions starting with Terminal 15 ON. Index Explanation Index ...

Functional Description (FUB) Washer pump for headlight washer system

... Domain Controller (BDC) activates the washer pump for the headlight cleaning system via a relay in the corresponding power distribution box. Item Explanation 1 Washer pump for headlight washer system Pin assignments Pin Explanation Terminal 30 Terminal 30 voltage supply via relay (the JBE or FEM or the Body Domain Controller activates the relay in the power distribution ...

Functional Description (FUB) DC/DC converter

... the terminal 30B DC/DC relay with constant voltage, also during the starting operation. The relay is located in the DC/DC converter. Index Explanation Index Explanation 1 DC/DC converter ...

Functional Description (FUB) Auxiliary battery

... battery is fitted for the power supply (24 Volts) of this power steering. By means of a cut-off relay, this auxiliary battery is switched into series with the vehicle battery. The EPS ... ;). The charging unit activates the cut-off relay. Note! The size of the auxiliary battery (Ah) depends on the equipment. Functional description A higher front axle load occurs due ...

Wiring Diagram (SSP) Fuse F35

Fuse F35 SP000005042510180Fuse F35 Z3 Fuse box 30 F504 250A RT 25.0 30<504 RT/WS 0.75 30B RT 0.75 30B<35 RT 1.5 30B<35 A16 Car access system A16*2B 11 Z1*11B 1 A34*3B 23 Z1*6B 1 X2085 4 Z3*15B K2085 DDE main relay X13*2B 3 Z1 Junction box4)Relay, terminal 30B A34 Z1_4 F35 10A 30B 4 0140 ...

Functional Description (FUB) Air supply system

... The compressor is driven by an electric motor. Voltage is supplied to the electric motor via a relay. The relay is activated by the EHC control unit until the specified nominal height is reached ... is supplied with voltage (terminal 30) via by the rear power distribution box via the compressor relay. Item Explanation Item Explanation 1 Electric motor 2 Discharge valve 3 Solenoid ...

Wiring Diagram (SSP) Fuse F137

Fuse F137 SP000005019010258Fuse F137 0.35 30B_1 RT/GN/GE RT/BR 0.35 30B<137 A16 Car access system B245 Fuel tank pressure sensor A16*1B 2 Z2*25B 1 Z2*1B 10 Z2 Fuse carrier, rear1)Relay, terminal 30B F137 5A 30B 1 Z2_1 Z2*7B 10 K5 Cut-out relay, electric fan K5*1B 1 X95*3B 3 Z3 Fuse box 30 F503 100A RT 16.0 30<503 Z3*4B 1 Z3 Fuse box 30 F506 150A RT 25.0 30< ...

Functional Description (FUB) Airbag sensors

... then determines the direction and intensity of the impact based on the data relayed by the sensors. The thresholds must be exceeded at two separate sensors before a crash is recognised ...

Wiring Diagram (SSP) Horn

Horn SP000005284110026Horn RT/BR 1.0 FANF RT/BR 1.0 FANF RT/BR 1.0 FANF RT/BR 1.0 FANF Z1*8B 6 5 X149*1B 4 H3*1B 2 1 30B 30B A34 31 F62 15A Z1 Junction box1)Horn relay Horn, low range ... with alarm system and au-tomatic air flap control withoutSports package RT/BR 1.0 FANF RT/BR 1.0 FANF RT/BR 1.0 FANF Z1*8B 6 H3*1B 2 1 30B 30B A34 31 F62 15A Z1 Junction box1)Horn relay Horn ...

Wiring Diagram (SSP) Fuse F48

... box2)Relay, terminal 15N F48 5A 15N A34 2 Z1*7B 1 A60 Electrochromic interior rearview mirror A60*1B 3 GN/BR 0.35 15N<48 B111 Engine breather heater B111*1B 1 GN/BR 0.35 15N<48 K2 Relay, secondary air pump K2*1B 1 GN/BR 0.5 15N<48 Y64 Engine mount changeovervalve X13*12B 12 GN/BR 0.35 15N<48 RT/GN 0.5 15N<48 X671*3B 3 Y64*1B 2 RT/GN 0.5 15N<48 ...

Wiring Diagram (SSP) Engine cooling system

... relay, electric fan Z2 Fuse carrier, rear 30B F137 5A Z3 Fuse box 30 F505 100A Z2*7B 10 Z3*3B K5*2B K5*1B 1 RT/BR 0.35 30B<137 K5*1B 2 BL/GE 0.35 L_REL RT 16.0 30<505 K5*3B Z4*3B 1 Z4*1B 1 M87*1B 2 RT 16.0 87<505 RT 16.0 87<505 Z4 Front power distribution box M87 Electric fan BR 16.0 31 SW/GN 0.5 T_ELUE Z10*15B 1 M87*1B 4 K5 Cut-out relay, electric fan Z1*9B 1 ...

Functional Description (FUB) Volume control valve and high pressure pump

... . This sets the necessary fuel mass flow for each load point. The quantity control valve is powered by the quantity control valve relay using terminal 15N. The engine control system activates the relay. Index Explanation Index Explanation 1 Volume control valve Pin assignments Pin Explanation Terminal 15N Voltage supply for quantity control valve PWM Pulse-width modulated ...

Functional Description (FUB) Heated rear window

... output. Relay activation for the heated rear window is performed by the junction box electronics (JBE). Item Explanation Item Explanation 1 Heated rear window 2 Bottom heated area 3 Rear ... for the relay activation): Fault entry in the junction box electronics (JBE) Possible damage to the heated wires can cause the radio to malfunction. A function check of the heated rear ...

Functional Description (FUB) Intelligent battery sensor

... actions, e.g. switch-off of terminal 30F In the time between engine OFF and switch-off of the DME main relay or DDE main relay, the intelligent battery sensor receives the following information from the engine control: Maximum charge volume that can be drawn for a reliable engine start. After the DME main relay has been switched off, the intelligent battery sensor ...

Wiring Diagram (SSP) Fuse F505

Fuse F505 SP0000050228 10333 Fuse F505 Z3 Fuse box 30 F505 100A RT 16.0 30<505 K5 Cut-out relay, electric fan G1 Battery Z3*3B K5*2B 0140 ...

Wiring Diagram (SSP) Engine cooling system
Applies to: TU

... sensor A460 Digital diesel electronics 15 A460 Digital diesel electronics 31 31 31 31 31 K5 Cut-out relay, electric fan Z2 Fuse carrier, rear 30B F137 5A Z3 Fuse box 30 F505 100A Z2*7B ... /GN 0.5 T_ELUE Z10*15B 1 M87*1B 4 K5 Cut-out relay, electric fan Z1*9B 1 2 K5*1B 5 1 K5*1B 3 fan 400/600 W fan 800/1000 W Z1 Junction box 15N F46 5A GN/RT 0.35 15N<46 Z1*7B 3 X148*1B ...

Wiring Diagram (SSP) Fuse F600

Fuse F600 SP000006294010937Fuse F600 Z9 Fuse box 2 30 F600 100A RT 16.0 30<600 Z9*3B B237*1B Z9*2B G6 Auxiliary battery B237 Gas generator, safety batteryterminal for starter unit RT 50.0 B+ K14 Cut-off relay K14*2B 0140 ...

Wiring Diagram (SSP) Fuse F73

Fuse F73 SP000005227910218Fuse F73 Z1 Junction box 30 F73 60A RT 10.0 30<73 RT 25.0 30<504 K5 Cut-out relay, electric fan Z3*15B Z3 Fuse box 30 F504 250A Z1*11B 1 K5*1B 3 Z1*9B 1 0140 ...

Functional Description (FUB) Operating principle of trailer charging cable

Operating principle of trailer charging cable Operating principle of trailer charging cable The trailer charging cable is switched on by a relay in the trailer module (AHM). It is connected to pin 10 of the trailer socket and serves to charge a battery in the trailer. The trailer charging cable is switched on and off according to the following preconditions: Switch ...

Functional Description (FUB) Slide/tilt sunroof

... to commands requesting operation of the slide/tilt sunroof by activating the two integral relays. The relays supply the appropriate drive units with voltage. The roof function centre (FZD) monitors the relay contacts to ensure correct actuation (glass slide/tilt sunroof panel and sliding headliner). Two hall effect sensors are integrated into every drive. The hall ...

Wiring Diagram (SSP) Fuse F17

Fuse F17 SP000005024310163Fuse F17 Z3 Fuse box 30 F504 250A RT 25.0 30<504 Z1*11B 1 Z1*3B 6 A58 Footwell module A58*3B 1 RT 2.5 30F<17 Z3*15B Z1 Junction box3)Bistable relay A34 31 31 F17 30A 30F 3 0140 ...

Wiring Diagram (SSP) Fuse F4
Applies to: NOT P185 (Marked special task vehicle) NOT P186 (Unmarked special task vehicle) -2012/06

Fuse F4 SP000005024710150Fuse F4 Z3 Fuse box 30 F504 250A RT 25.0 30<504 Z1*11B 1 Z1*5B 3 A88 Controller A88*1B 1 RT/GE 0.35 30F<4 Z3*15B Z1 Junction box3)Bistable relay A34 31 31 F4 5A 30F 3 0140 ...

Wiring Diagram (SSP) Fuse F18

Fuse F18 SP000005024410164Fuse F18 Z3 Fuse box 30 F504 250A RT 25.0 30<504 Z1*11B 1 Z1*3B 6 A58 Footwell module A58*3B 3 RT/BL 2.5 30F<18 Z3*15B Z1 Junction box3)Bistable relay A34 31 31 F18 30A 30F 3 0140 ...

Wiring Diagram (SSP) Fuse F36

Fuse F36 SP000005198510181Fuse F36 Z3 Fuse box 30 F504 250A RT 25.0 30<504 RT/GN 2.5 87<36 Z1*11B 1 Z1 Junction box5)Washer pump relay F36 30A 87 5 A34 Z1*2B 1 M93 Washer pump for headlightwasher system M93*1B 2 Z3*15B 0140 ...

Wiring Diagram (SSP) Fuse F1

Fuse F1 SP000005024210147Fuse F1 Z3 Fuse box 30 F504 250A RT 25.0 30<504 Z1*11B 1 Z1*5B 6 A58 Footwell module A58*3B 2 RT/GN 1.5 30F<1 Z1 Junction box3)Bistable relay A34 31 31 F1 10A 30F 3 Z3*15B 0140 ...

Wiring Diagram (SSP) Fuse F16

Fuse F16 SP000005024610162Fuse F16 Z3 Fuse box 30 F504 250A RT 25.0 30<504 Z1*11B 1 Z1*3B 7 A58 Footwell module A58*2B 2 RT/WS 4.0 30F<16 Z3*15B Z1 Junction box3)Bistable relay A34 31 31 F16 40A 30F 3 0140 ...

Wiring Diagram (SSP) Fuse F11
Applies to: NOT P1CC (Automatic Start/Stop function)

Fuse F11 SP000005024810157Fuse F11 Z3 Fuse box 30 F504 250A RT 25.0 30<504 Z1*11B 1 A34*3B 1 A95 Heating/air conditioning system A95*2B 1 RT/GN 0.75 30F<11 Z1 Junction box3)Bistable relay F11 7.5A 30F A34 31 31 3 Z3*15B 0140 ...

Wiring Diagram (SSP) Fuse F3

Fuse F3 SP000005024110149Fuse F3 Z3 Fuse box 30 F504 250A RT 25.0 30<504 RT/BL 0.35 30F<3 Z1*11B 1 Z1*5B 4 A51 Central gateway module X6 Diagnosis socket A51*1B 39 RT/BL 0.35 30F<3 X6*1B 16 Z1 Junction box3)Bistable relay A34 F3 5A 30F 31 31 3 Z3*15B 0140 ...

Functional Description (FUB) Rear window aerial

... control service (remote control service aerial) in the rear window and then relayed to the remote-control receiver. The following graphic shows the rear window aerial using the example ... to the TV amplifier in the individual wave trap are also relayed through these wires. Item Explanation 1 Rear window with aerials 2 Bottom heated area 3 Rear window 4 Field for AM ...

Can't find what you're looking for? Keep the following in mind for better results:
  • This site is a translation of the original German documentation into international English, and therefore things may be called differently from what you're used to in your dialect (think for example: subframe vs. axle carrier, bushing vs. rubber mount, differential vs. final drive, sway bar vs. anti-roll bar, and so forth)
  • There may not be a writeup specifically on "replacing subframe bushes", because it is incorporated into a larger one for "removing the axle carrier". Try broadening the scope if your search comes up empty.
  • When there are too many matches, only the most relevant results are displayed.
Sponsored links