Repair Instructions (REP) Check the timing for the camshafts on the right (N62/N62TU)

11 31 071 Check the timing for the camshafts on the right (N62/N62TU) 11 9 190 11 9 461 11 9 462 (cylinder bank 1 to 4) Necessary preliminary tasks: Remove servomotor for right ... firing position of 1st cylinder. Note: In the TDC firing position, the cam of the exhaust camshaft at cylinder 1 will point diagonally up. The cam of the intake camshaft points diagonally ...

Repair Instructions (REP) Removing and installing/replacing left exhaust camshaft (N62/N62TU)

... . Note: Camshaft has a groove and sensor wheel has a lug for fastening purposes. Fit sensor wheel (1) and align to groove in camshaft. Insert screw (2) and tighten down. Tightening torque 11 ... 11 31 036 Removing and installing/replacing left exhaust camshaft (N62/N62TU) (cylinder bank 5 to 8) Necessary preliminary tasks: Remove servomotor for left eccentric shaft Remove ...

Repair Instructions (REP) Removing and installing/replacing right exhaust camshaft (N62/N62TU)

... ). Release screw (2) and remove sensor wheel (1). Installation: Installation of exhaust camshaft is described separately from removal. Clean all bearing positions and cams of exhaust camshaft and lubricate with engine oil. Note: Camshaft has a groove and sensor wheel has a lug for fastening purposes. Fit sensor wheel (1) and align to groove in camshaft. Insert screw (2 ...

Repair Instructions (REP) Checking camshaft timing on left side (N62/N62TU)

11 31 070 Checking camshaft timing on left side (N62/N62TU) 11 9 190 11 9 461 11 9 462 (cylinder bank 5 to 8) Necessary preliminary tasks: Remove servomotor for left eccentric shaft ... : With 1st cylinder in firing TDC position, cams of inlet and exhaust camshafts at 5th cylinder point upwards at an angle as shown in illustration. Note: Alignment hole for TDC position ...

Wiring Diagram (SSP) Intake camshaft

Intake camshaft SP0000024379C1372Intake camshaft A4010 Junction box 87 F35 30A 87 F36 30A B62141 Intake camshaft sensor B62241 Intake camshaft sensor 2 Y6281 VANOS solenoid valve, intake Y6283 VANOS solenoid valve 2, intake A6000 DME control unit 31 31 31 31 31 OR 0.5 87<36 OR 0.5 87<35 SW/WS 0.5 M_DIGIT GE 0.5 P_NWGE1 WS 0.5 T_NWE1 OR 0.5 87<35 SW/WS 0.5 ...

Wiring Diagram (SSP) Exhaust camshaft

... X6021 8 6 B62142 Exhaust camshaft sensor B62242 Exhaust camshaft sensor 2 Y6282 VANOS solenoid valve, exhaust Y6284 VANOS solenoid valve 2, ex-haust X6021 8 6 A6000 DME control unit 31 ... Exhaust camshaft SP0000024380C1373Exhaust camshaft A4010 Junction box 87 F35 30A 87 F36 30A OR 0.5 87<35 OR 0.5 87<36 SW/WS 0.5 M_DIGIT GE/BL 0.5 P_NWGA1 WS/BL 0.5 T_NWA1 OR 0.5 ...

Repair Instructions (REP) Removing and installing/replacing right intake camshaft (N62 from 9/03 and N62TU)

... be necessary if after the intake camshaft has been removed the eccentric shaft is also to be removed. If necessary, remove eccentric shaft sensor (2). Note: Removal of the intermediate ... rectangular compression ring (1) apart and remove towards front. Note: Intake camshaft of cylinder bank 1 to 4 is marked with ”EIN 14”. If necessary, replace sensor wheel (1). Release screw (2 ...

Repair Instructions (REP) Removing and installing/replacing left intake camshaft (N62 from 9/03 and N62TU)

... : This operation will only be necessary if after the intake camshaft has been removed the eccentric shaft is also to be removed. If necessary, remove eccentric shaft sensor (2). Note ... . Carefully pull plain rectangular compression ring (1) apart and remove towards front. Note: Intake camshaft of cylinder bank 5 to 8 is marked with ”EIN 58”. If necessary, replace sensor wheel ...

Tightening Torques (AZD) Camshaft

... for sliding and tensioning rails M41 M47 M47TU M51 M57 M57TU M16 x 1.5 20 Nm M67 M16 x 1.5 26 Nm 13AZ Signal disk to camshaft S62 S54 M16 x 1.5 50 Nm 14AZ Sensor gear to camshaft N62 N62TU ... 11 Engine 11 31 Camshaft Type Thread Tightening specification Measure 6AZ Flange to camshaft M30 145 Nm 7AZ Screw plug for chain tensioner M50 S50 US S62 M22 x 1.5 50 Nm M22 x 1.5 40 ...

Repair Instructions (REP) Adjusting camshaft timing on right side (N62 / N62TU)

11 31 574 Adjusting camshaft timing on right side (N62 / N62TU) 11 9 190 11 9 460 11 9 461 11 9 462 11 9 463 (cylinder bank 1 to 4) Necessary preliminary tasks: Are described in the operation ”Checking camshaft timing on right side”. Remove right timing case cover Note: When slackening screws, grip camshafts at hexagon head. Slacken screws of exhaust and inlet ...

Repair Instructions (REP) Adjusting camshaft timing on left side (N62 / N62TU)

11 31 573 Adjusting camshaft timing on left side (N62 / N62TU) 11 9 190 11 9 460 11 9 461 11 9 462 11 9 463 (cylinder bank 5 to 8) Necessary preliminary tasks: Check camshaft timing on left side Remove left timing case cover Note: When slackening screws, grip camshafts at hexagon head. Slacken screws of exhaust and inlet adjustment unit. Get special tool kit 11 9 460 ...

Tightening Torques (AZD) Camshaft

11 Engine 11 31 Camshaft Type Thread Tightening specification Measure 1AZ Camshaft bearing cap M6 10 Nm M7 14 Nm M7- 8.8 15 Nm M8 20 Nm 2AZ Sprocket to camshaft M20 M21 M40 M10 65 Nm 3AZ Sprocket to camshaft flange M60 M62 M6 15 Nm M6 10 Nm M50 M52 M52TU M54 M56 S52 S50 US M50 VANOS M7 Application torque 5 Nm Jointing torque 20 Nm M7 15 Nm 4AZ Sprocket to camshaft ...

Repair Instructions (REP) Replacing pulse generator on right exhaust camshaft (N62TU)

12 14 513 Replacing pulse generator on right exhaust camshaft (N62TU) (cylinder bank 1 to 4) Necessary preliminary tasks: Read out fault memory of DME control unit; if necessary, work through test schedules Switch off ignition Remove intake filter housing Release screws and remove holder (1). Remove right ignition coil cover (2). Release plug connector (1) and pull ...

Repair Instructions (REP) Replacing pulse generator on right inlet camshaft (N62TU)

12 14 526 Replacing pulse generator on right inlet camshaft (N62TU) (cylinder bank 1 to 4) Necessary preliminary tasks: Read out fault memory of DME control unit; if necessary, work through test schedules Switch off ignition Remove intake filter housing Release screws and remove holder (1). Remove right ignition coil cover (2). Release plug connector (1) and pull off ...

Repair Instructions (REP) Replacing pulse generator on left inlet camshaft (N62TU)

12 14 522 Replacing pulse generator on left inlet camshaft (N62TU) (cylinder bank 5 to 8) Necessary preliminary tasks: Read out fault memory of DME control unit; if necessary, work through test schedules Switch off ignition Remove intake filter housing Release screws and remove holder (1). Remove left ignition coil cover (2). Release plug connector (1) and pull off ...

Repair Instructions (REP) Replacing pulse generator on left exhaust camshaft (N62TU)

12 14 512 Replacing pulse generator on left exhaust camshaft (N62TU) (cylinder bank 5 to 8) Necessary preliminary tasks: Read out fault memory of DME control unit; if necessary, work through test schedules Switch off ignition. Remove intake filter housing Release screws and remove holder (1). Remove left ignition coil cover (2). Release plug connector (1) and pull ...

Repair Instructions (REP) Replacing solar rain/light sensor and fogging sensor

61 35 688 Replacing solar rain/light sensor and fogging sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection) . Necessary preliminary ... and condensation sensor (1) from windscreen. Installation: Close plug connection (2) only after fitting solar rain/light and condensation sensor on windscreen! Carefully clean windscreen ...

Repair Instructions (REP) Adjust ACC sensor
Applies to: 2010/03+

66 31 001 Adjust ACC sensor 36 1 100 Special tool required: Active Cruise Control ACC adjusting device, complete. Order number: 81 10 0 021 292 Consisting of: Mirror, complete Wheel ... : To set the ACC sensor, connect the BMW diagnosis system and fit the ACC adjusting device. Select ACC calibration in diagnosis. Service function Chassis and suspension ACC cruise control ...

Repair Instructions (REP) Overview of sensors for airbag system

65 77 ... Overview of sensors for airbag system Airbag control unit (under centre console) Acceleration sensors, front (left/right) Sensor, front door (left/right) Sensor, B-pillar (left/right) ...

Repair Instructions (REP) Replacing a rear pulse sensor

... in the holders. Release Torx socket screw (1). Withdraw wheel speed sensor (2) from bore hole. Installation: Tightening torque 34 51 3AZ. Clean bore for pulse generator and lubricate with Staburags NBU 12/K lubricating grease. Important! Check sensor head prior to installation for external damage, replacing if necessary. ...

Repair Instructions (REP) Overview, rain sensor (additional work when replacing the windscreen / sensor replacement)

61 35 ... Overview, rain sensor (additional work when replacing the windscreen / sensor replacement) 1-Series: E8x 3-Series: E9x 5-Series: E6x 6-Series: E6x X1: E84 Z4: E89 Sensor type/ Sensor shape With windscreen replacement replacement sensor required When replacing the sensor/ Programming/encoding necessary When replacing the sensor/ Initialisation required ...

Repair Instructions (REP) Replacing evaporator temperature sensor

64 11 942 Replacing evaporator temperature sensor Necessary preliminary tasks: Remove panel for pedal assembly Pull out temperature sensor (1) and disconnect associated plug connection. ...

Technical Data (TED) Camshaft

11 31 Camshaft BMW N62TU Guide bearing (width) mm 14.100 +0.043 Radial runout mm 0.040 ... 0.082 Axial play mm 0.065 ... 0.150 ...

Repair Instructions (REP) Removing and installing (replacing) ACC sensor
Applies to: 2010/03+

66 31 006 Removing and installing (replacing) ACC sensor Necessary preliminary work: Remove front bumper trim Note: For a better view, graphic shows rear view with bumper support and ACC sensor removed. Undo screws in marked area on the rear side of the ACC sensor (1). Tightening torque 66 31 1AZ. Remove ACC sensor (1) from holder (2). Important! Secure ACC sensor (2 ...

Repair Instructions (REP) Replacing rain/light solar sensor
Applies to: -2008/10

61 35 685 Replacing rain/light solar sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection) . Necessary preliminary tasks: Remove interior rearview mirror Disconnect plug connection (1). Unlock metal spring (3) in direction of arrow. Pull off solar rain/light sensor (2) from windscreen. Installation: Close plug ...

Repair Instructions (REP) Replacing a brake pad sensor (front)

34 35 001 Replacing a brake pad sensor (front) Important! The brake pad wear sensor must be replaced once it has been removed (brake pad wear sensor loses its retention capability in the brake pad). If a brake pad sensor that has already been ground has to be replaced even though the minimum brake pad thickness has not yet been reached, you must observe the following ...

Repair Instructions (REP) Initializing rain/light (solar) sensor

61 35 679 Initializing rain/light (solar) sensor Note: Initialization is necessary: after replacing windscreen after replacing rain/light (solar) sensor after replacing optical element on rain/light (solar) sensor after installing a used rain/light (solar) sensor Note: Connect BMW diagnosis system Initializing rain/light (solar) sensor ...

Repair Instructions (REP) Replacing a brake pad sensor (rear)

34 35 513 Replacing a brake pad sensor (rear) Important! The brake pad wear sensor must be replaced once it has been removed (brake pad wear sensor loses its retention capability in the brake pad). If a brake pad sensor that has already been ground has to be replaced even though the minimum brake pad thickness has not yet been reached, you must observe the following ...

Repair Instructions (REP) Replacing one front pulse sensor

... of bore. Installation: Tightening torque 31 51 3AZ. Clean bore for pulse sensor and lubricate with Staburags NBU 12/K lubricating grease. Important! Check sensor head prior ... 34 52 525 Replacing one front pulse sensor Important! Read and comply with notes on protection against electrostatic discharge (ESD protection). Necessary preliminary tasks: Read ...

Repair Instructions (REP) Replacing (one) temperature sensor for heater

64 11 939 Replacing (one) temperature sensor for heater Necessary preliminary tasks: Remove front speaker carrier Unlock temperature sensor (1) and feed out. Disconnect cables (1). Connect cables to new temperature sensor with butt connectors and heat-shrink sleeves. Insulate cables with insulating tape. ...

Repair Instructions (REP) Information on intelligent battery sensor (IBS)

61 12 ... Information on intelligent battery sensor (IBS) Notice! Do not connect the charger to the 12 V charging socket The 12 V charging socket is supplied with voltage by the rear ... connection between the IBS and the sensor screw. Do not use force when disconnecting the pole shoe from the battery terminal: Do not pull on the ground cable. Do not place any tools under ...

Tightening Torques (AZD) Variable Camshaft Control

... camshaft M62 VANOS M12x1.5 110 Nm 15AZ Left-hand thread: Nut of sensor gear screw fitting M62 VANOS M18x1.5 40 Nm 16AZ Adjustment unit to exhaust or inlet camshaft N40 N42 N45 N46 M10x1 ... 11 Engine 11 36 Variable Camshaft Control Type Thread Tightening specification Measure 1AZ 4/2-way valve/solenoid valve to VANOS housing M52 M52TU M54 M56 S52 S50 US M50 VANOS 30 Nm ...

Repair Instructions (REP) Replacing optics for solar rain/light sensor

61 35 683 Replacing optics for solar rain/light sensor Attention! Read and comply with notes on protection against electrostatic damage (ESD protection). Necessary preliminary work: Remove rain/light solar sensor Replacement lenses are permitted for motor vehicles with rain/light/solar sensor only. Replacement lenses must not be used on vehicles with head‐up display ...

Repair Instructions (REP) Replacing fogging sensor (from 10/2008)
Applies to: 2008/10+

64 11 970 Replacing fogging sensor (from 10/2008) 00 9 317 Warning! Make sure rooms are well ventilated when working with adhesive remover indoors. Important! Do not under any ... ). Note: If necessary, carefully heat fogging sensor (2) with a hot air blower to approx. 40-60 °C. Lift off fogging sensor (2) with special tool  00 9 317 and slowly pull off from ...

Repair Instructions (REP) Replacing fogging sensor (up to 10/2008)
Applies to: -2008/10

64 11 970 Replacing fogging sensor (up to 10/2008) Necessary preliminary tasks: Remove two-part mirror base cover Unclip fogging sensor (1) from retaining tabs (2). Disconnect plug connection (3). Installation: Make sure fogging sensor (1) is securely seated. Installation: Sensor surface (1) must be clean and free from grease. ...

Repair Instructions (REP) Carrying out steering angle sensor adjustment

61 31 996 Carrying out steering angle sensor adjustment Important! In vehicles with active steering, steering angle sensor adjustment is integrated in the service function ”Initial operation/adjustment for active steering” and must not be carried out separately! Note: Steering angle sensor adjustment must be carried out: Before adjustment work on the front axle ...

Repair Instructions (REP) Replacing front right ride-height sensor

37 14 511 Replacing front right ride-height sensor Important! Observe safety instructions for raising the vehicle Note: Jointed rod on upper control arm 37 14 5AZ. Important! Read ... nut (2) and disconnect jointed rod. Installation: Sensor lever (3) must point from ride-height sensor to right front wheel. Replace self-locking nut. Tightening torque 37 14 4AZ ...

Repair Instructions (REP) Removing and installing/replacing steering angle sensor

32 31 082 Removing and installing/replacing steering angle sensor Note: Steering angle sensor is integrated in steering-column switch cluster. After installation: Replacement only: Carry out programming/encoding Carry out steering angle sensor adjustment/adjustment for active front steering ...

Repair Instructions (REP) Removing and installing/replacing outside temperature sensor

65 81 060 Removing and installing/replacing outside temperature sensor Necessary preliminary tasks: Remove front bumper panel Disconnect plug connection (1). Press out outside temperature sensor (2) in direction of arrow and remove. Installation note: Outside temperature sensor must audibly snap into place. Check for secure seating after fitting. ...

Repair Instructions (REP) Replacing front left ride-height sensor

37 14 521 Replacing front left ride-height sensor Important! Observe safety instructions for raising the vehicle Note: Jointed rod on upper control arm 37 14 5AZ. Important! Read ... slip out when coolant expansion tank is removed. Release screw (1). Installation: Align ride-height sensor holder by means of lug (2) to opening under screw (1). Tightening torque 37 ...

Repair Instructions (REP) Replacing left knock sensors (N62, N62TU)

12 14 611 Replacing left knock sensors (N62, N62TU) (cylinder bank 5 to 8) Necessary preliminary tasks: Read out fault memory of DME control unit Check stored fault messages Switch off ignition Remove intake air manifold Important! Mixing up the knock sensor plug connections will result in engine damage! Routing of wires and plug connections must conform ...

Repair Instructions (REP) Replacing right knock sensors (N62, N62TU)

12 14 610 Replacing right knock sensors (N62, N62TU) (cylinder bank 1 to 4) Necessary preliminary tasks: Read out fault memory of DME control unit Check stored fault messages Switch off ignition Remove intake air manifold Important! Mixing up the knock sensor plug connections will result in engine damage! Routing of wires and plug connections must conform ...

Repair Instructions (REP) Replacing coolant temperature sensor (N62, N62TU)

13 62 531 Replacing coolant temperature sensor (N62, N62TU) Warning! Danger of scalding! Only perform these tasks on an engine that has cooled down. Necessary preliminary tasks: Read ... . Observe country-specific waste-disposal regulations. Coolant temperature sensor is mounted on water pipe at front. Unlock plug (1) and remove. Release temperature sensor (2 ...

Repair Instructions (REP) Removing and installing/replacing front right sensor

65 77 534 Removing and installing/replacing front right sensor Operation is identical to: Removing and installing/replacing front left sensor ...

Repair Instructions (REP) Removing and installing/replacing front left sensor

65 77 532 Removing and installing/replacing front left sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Necessary preliminary tasks: Remove radiator air duct Release screws (1). Remove sensor (2) and disconnect associated plug connection. Tightening torque 65 77 6AZ. Installation: Replace screws (1). Important ...

Repair Instructions (REP) Removing and installing / replacing lateral acceleration sensor

37 14 610 Removing and installing / replacing lateral acceleration sensor Important! Read and comply with notes on protection against electrostatic discharge (ESD protection ... ), disconnect plug connection (2) and remove lateral acceleration sensor (3). Installation: Replace self-locking nuts. Tightening torque 37 14 7AZ. After installation: If necessary, carry ...

Repair Instructions (REP) Replacing left oxygen monitor sensor (N62 / N62TU)

11 78 540 Replacing left oxygen monitor sensor (N62 / N62TU) 11 7 030 (cylinder bank 5 to 8) Necessary preliminary tasks: Switch off ignition. Remove rear underbody protection Warning! Scalding hazard! Only perform this task on an engine that has cooled down. Unlock and detach plug connection (1) for monitor sensor (2). Unclip monitor sensor cable. Release monitor ...

Repair Instructions (REP) Replacing right oxygen monitor sensor (N62/N62TU)

11 78 543 Replacing right oxygen monitor sensor (N62/N62TU) 11 7 030 (cylinder bank 1 to 4) Necessary preliminary tasks: Switch off ignition Remove rear underbody protection Warning! Scalding hazard! Only perform this task on an engine that has cooled down. Unlock and detach plug connection (1) for monitor sensor (2). Unclip monitor sensor cable. Release monitor ...

Repair Instructions (REP) Replacing right oxygen control sensor (N62/N62TU)

11 78 533 Replacing right oxygen control sensor (N62/N62TU) 11 7 030 (cylinder bank 1 to 4) Necessary preliminary tasks: Switch off ignition. Remove reinforcement plate Warning! Scalding hazard! Only perform this task on an engine that has cooled down. Release plug connector (1) and pull off. Unclip control sensor cable. Release control sensor (2) with special tool ...

Repair Instructions (REP) Replacing left oxygen control sensor (N62/N62TU)

11 78 530 Replacing left oxygen control sensor (N62/N62TU) 11 7 030 11 9 150 (cylinder bank 5 to 8) Necessary preliminary work: Switch off ignition. Remove reinforcement plate. Remove front propeller shaft (E7X only). Warning! Risk of burning! Only perform this task on an engine that has cooled down. Unlock plug connector (3) and pull off. Unclip control sensor cable ...

Repair Instructions (REP) Removing and installing/replacing a front ultrasonic sensor (centre)

66 20 518 Removing and installing/replacing a front ultrasonic sensor (centre) Necessary preliminary work: Remove front bumper panel Disconnect plug connection (1) and unclamp ultrasonic sensor from retaining lugs (2). Installation note: Before installation of ultrasonic sensor on wiring harness, clean plug connection! Retaining lugs (2) must not be damaged! Make ...

Repair Instructions (REP) Replacing rear left or right ride-height sensor

37 14 515 Replacing rear left or right ride-height sensor Important! Observe safety instructions for raising the vehicle Note: Ride-height sensor holder on rear axle carrier 37 14 2AZ ...  (2) and disconnect jointed rod. Installation: Sensor lever (3) must point from ride-height sensor to respective rear wheel. Replace self-locking nut. Tightening torque 37 14 4AZ ...

Repair Instructions (REP) Removing and installing/replacing DSC rotation-rate sensor

34 52 550 Removing and installing/replacing DSC rotation-rate sensor Important! Read and comply with notes on protection against electrostatic discharge (ESD protection). Important! Do ... screws. Tightening torque 34 51 2AZ. Disconnect plug connection and remove yaw sensor (1). Carry out calibration/adjustment of DSC sensor. ...

Repair Instructions (REP) Removing and installing (replacing) left B-pillar sensor

65 77 720 Removing and installing (replacing) left B-pillar sensor Warning! Note airbag safety instructions! Incorrect handling can activate airbag and cause injury. Necessary ... sensor and disconnect associated plug connection. Tightening torque 65 77 3AZ. Installation: Establish correct positioning of B-pillar sensor (1) by means of guide pin (2) and screw (3). ...

Repair Instructions (REP) Replacing sensor mat for driver's seat occupancy detector

65 77 598 Replacing sensor mat for driver's seat occupancy detector Operation is described in: Replacing sensor mat for passenger seat occupancy detector ...

Repair Instructions (REP) Removing and installing/renewing right front door sensor

65 77 745 Removing and installing/renewing right front door sensor This operation is described in: Removing and installing (replacing) left front door sensor ...

Repair Instructions (REP) Removing and installing/replacing inside mirror (with rain sensor)

51 16 060 Removing and installing/replacing inside mirror (with rain sensor) Important! Work may only be carried out at a room/object temperature of 18 ... 28 °C. If this can ... or after disconnecting inside mirror plug connection or battery. If necessary, calibrate compass in interior rearview mirror. E60 Security version: Rain sensor is not installed, cable ...

Repair Instructions (REP) Removing and installing (replacing) left front door sensor

65 77 740 Removing and installing (replacing) left front door sensor Warning! Note airbag safety regulations! Incorrect handling can activate airbag and cause injury. Necessary preliminary tasks: Partially detach sound insulation Release screw (1). Tightening torque 65 77 4AZ. Remove sensor with pin (2) from door panel fit (3) towards rear and disconnect associated ...

Repair Instructions (REP) Removing and installing/replacing differential pressure sensor (N62TU)

13 62 010 Removing and installing/replacing differential pressure sensor (N62TU) Necessary preliminary tasks: Read out fault memory of Digital Motor Electronics (DME) control unit ... 13 62 1AZ. Pull differential pressure sensor (1) out of intake air manifold. Installation: Now clear the fault memory. ...

Repair Instructions (REP) Removing and installing/replacing one ultrasonic sensor, front (side)

66 20 520 Removing and installing/replacing one ultrasonic sensor, front (side) Necessary preliminary work: Remove front bumper panel Disconnect plug connection (1) and remove rubber grommet (2). Installation note: Make sure rubber grommet (2) is correctly fitted! Unlock the retaining tabs (1) in the direction of the arrow and pull out the ultrasonic sensor (2) from ...

Repair Instructions (REP) Performing vertical acceleration sensor adjustment (vertical dynamics management)

37 .. ... Performing vertical acceleration sensor adjustment (vertical dynamics management) Note: Vertical acceleration sensor adjustment must be performed after replacement of the spring strut/shock absorber with damper satellites. Connect vehicle to BMW diagnosis system. Select and perform vertical acceleration sensor adjustment under Service functions. ...

Repair Instructions (REP) Removing and installing/replacing air-mass flow sensor (N62TU)

13 62 560 Removing and installing/replacing air-mass flow sensor (N62TU) Necessary preliminary tasks: Read out fault memory of DME control unit; if necessary, work through test schedules Switch off ignition Remove intake hose Unlock plug (1) and remove. Release screws. Remove air-mass flow sensor (2). Installation: Check sealing ring between air-mass flow sensor ...

Repair Instructions (REP) Removing and installing/replacing fuel level sensor (petrol, right)

16 12 000 Removing and installing/replacing fuel level sensor (petrol, right) Recycling Fuel escapes when fuel lines are detached. Have a suitable collecting vessel ready. Catch and dispose of escaping fuel. Observe country-specific waste disposal regulations. Note: When the right fuel level sensor is replaced, the left fuel level sensor must also be replaced ...

Repair Instructions (REP) Removing and installing/replacing left fuel level sensor (petrol)

16 12 001 Removing and installing/replacing left fuel level sensor (petrol) Recycling Fuel escapes when fuel lines are detached. Have a suitable collecting vessel ready. Catch ... (2). Release nuts (1) and remove cover for sensor opening (2) from left side of fuel tank. Disconnect plug connection (1). Unlock quick-release fastener (2) and detach fuel feed line ...

Repair Instructions (REP) Removing and installing/replacing emergency power siren with tilt sensor

65 75 055 Removing and installing/replacing emergency power siren with tilt sensor Necessary preliminary tasks: Remove front left wheel arch cover Note: On RHD vehicles remove front ... associated plug connection. Replacement: Release nut (1) and remove emergency power siren with tilt alarm sensor (2). Important! Risk of damage! Guides (1) of emergency power siren (2 ...

Functional Description (FUB) The temperature sensors

Notes on BMW DIAGNOSIS SYSTEM The temperature sensors Back Ventilation temperature sensor, footwell temperature sensor, outside temperature sensor The setpoint values for the blow-out ... and ventilation areas are monitored by footwell temperature sensors and the ventilation temperature sensors. If necessary, the stepper motors of the mixing flaps and the stratification ...

Functional Description (FUB) The temperature sensors

Notes on BMW DIAGNOSIS SYSTEM The temperature sensors Back Ventilation temperature sensor, footwell temperature sensor, outside temperature sensor The system calculates the setpoint ... area and the ventilation area are monitored using the footwell temperature sensors and ventilation temperature sensors. If necessary, the stepper motors of the mixing flaps ...

Wiring Diagram (SSP) Airbag sensors
Applies to: acsm2

Airbag sensors SP0000024442C1016Airbag sensors A173 Airbag sensor, left B-pillar BL/GE 0.35 SSBLY+ BL/GR 0.35 SSBLY- GR/GN 0.35 SSBLX- GR/WS 0.35 SSBLX+ 2 3 4 X10473 1 BL/BR 0.35 SSBRY+ BL/SW 0.35 SSBRY- GR/VI 0.35 SSBRX- GR/GE 0.35 SSBRX+ B78 Airbag sensor, front left door B79 Airbag sensor, front right door WS/SW 0.35 SSTLY+ WS/GN 0.35 SSTLY- 1 X1885 2 OR/GN 0.35 ...

Wiring Diagram (SSP) Sensor system
Applies to: dxc_70

Sensor system SP0000024458C1026Sensor system B4 Rear left wheel speed sensor B9801 DSC sensor B3 Rear right wheel speed sensor B2 Front left wheel speed sensor B1 Front right wheel speed sensor A149a Car access system 31 B16a Brake pad wear sensor, frontleft B17a Brake pad wear sensor, rearright A65a Dynamic stability control (DSC) 15 31 15 31 15 31 15 31 15 15 30 31 ...

Repair Instructions (REP) Removing and installing/replacing sensor for automatic recirculated air control (AUC)

64 11 990 Removing and installing/replacing sensor for automatic recirculated air control (AUC) Necessary preliminary tasks: Remove right microfilter housing cover Disconnect plug connection (1). Unlock AUC sensor (2) and remove. Installation: Make sure AUC sensor (2) is securely seated. ...

Repair Instructions (REP) Removing and installing/replacing a rear ultrasonic sensor (Park Distance Control)

66 20 540 Removing and installing/replacing a rear ultrasonic sensor (Park Distance Control) Necessary preliminary work: Remove rear bumper panel Disconnect plug connection (1 ... out of bracket. Installation note: Before installation of ultrasonic sensor (2) on wiring harness, clean plug connection! Installation note: Make sure rubber ring (1) is correctly seated ...

Wiring Diagram (SSP) Crankshaft sensor

Crankshaft sensor SP0000024373C1292Crankshaft sensor B6203a Crankshaft sensor A6000 DME control unit 31 31 A4010 Junction box 87 F35 30A OR 0.5 87<35 GE/WS 0.5 P_KWG SW/WS 0.5 M_DIGIT X6450 X11005 4 X6203 2 3 X60003 37 27 X6203 1 0140 ...

Repair Instructions (REP) Replacing temperature sensor for electric auxiliary heater - 3rd seat row -

64 12 685 Replacing temperature sensor for electric auxiliary heater - 3rd seat row - Necessary preliminary tasks: Remove centre console - 3rd seat row - Note: The following pictures show the seat cushion removed for purposes of clarity. Unlock temperature sensor (1) and disconnect associated plug connection. ...

Repair Instructions (REP) Removing and installing/replacing right eccentric shaft sensor (N62/N62TU)

11 37 040 Removing and installing/replacing right eccentric shaft sensor (N62/N62TU) (cylinder bank 1 to 4) Necessary preliminary tasks: Remove right cylinder head cover Unfasten screws. Remove eccentric shaft sensor (1). Installation: Read out fault memory of control unit of Digital Motor Electronics (DME). Check stored fault messages. Rectify faults. Now clear ...

Repair Instructions (REP) Removing and installing/replacing left eccentric shaft sensor (N62/N62TU)

11 37 035 Removing and installing/replacing left eccentric shaft sensor (N62/N62TU) (cylinder bank 5 to 8) Necessary preliminary tasks: Remove left cylinder head cover Unfasten screws. Remove eccentric shaft sensor (1). Installation: Read out fault memory of control unit of Digital Motor Electronics (DME). Check stored fault messages. Rectify faults. Now clear ...

Repair Instructions (REP) Removing and installing/replacing gyro sensor drive for Car Communication Computer

65 83 590 Removing and installing/replacing gyro sensor drive for Car Communication Computer Important! Read and comply with notes on protection against electrostatic damage (ESD ... strip (3) are correctly seated. Release bolt (1). Detach gyro sensor for Car Communication Computer (2) in direction of arrow from plug-in contact (3). ...

Repair Instructions (REP) Replacing sensor mat (OC3 mat) for passenger seat occupancy detector

65 77 604 Replacing sensor mat (OC3 mat) for passenger seat occupancy detector Warning! Note airbag safety instructions! Incorrect handling can activate airbag and cause injury. Warning! US/CDN front passenger seat (with OC3 mat) only: A defective OC3 mat can only be replaced together with the padding and the seat cover. New OC3 mat is supplied with padding, seat ...

Repair Instructions (REP) Removing and installing/renewing ventilation temperature sensor (centre fresh-air grille)

64 11 906 Removing and installing/renewing ventilation temperature sensor (centre fresh-air grille) Necessary preliminary tasks: Remove centre fresh-air grille Disconnect plug connection (1). Turn temperature sensor (2) in direction of arrow as far as it will go. Remove temperature sensor (2) from centre fresh-air grille (4). Installation: On version with two ...

Repair Instructions (REP) Removing and installing/replacing fuel level sensor (left petrol with delivery unit)

16 12 001 Removing and installing/replacing fuel level sensor (left petrol with delivery unit) Recycling Fuel escapes when fuel lines are detached. Have a suitable collecting vessel ... on vehicles with a 3rd row of seats Remove right sensor unit For E70 without 3rd row of seats only: Only unclip seat bench (1) as shown on the left and right and fold up in direction ...

Can't find what you're looking for? Keep the following in mind for better results:
  • This site is a translation of the original German documentation into international English, and therefore things may be called differently from what you're used to in your dialect (think for example: subframe vs. axle carrier, bushing vs. rubber mount, differential vs. final drive, sway bar vs. anti-roll bar, and so forth)
  • There may not be a writeup specifically on "replacing subframe bushes", because it is incorporated into a larger one for "removing the axle carrier". Try broadening the scope if your search comes up empty.
  • When there are too many matches, only the most relevant results are displayed.
Sponsored links