Functional Description (FUB) Ambient pressure sensor

Ambient-pressure sensor Ambient pressure sensor The ambient-pressure sensor is installed directly in the engine control unit; it s seated as a separate component on the printed-circuit board. In the engine control unit, the value is checked to ensure it remains within permitted limits. A fault code is entered if the ambient pressure is not within the expected range ...

Repair Instructions (REP) Replacing evaporator temperature sensor

64 11 943 Replacing evaporator temperature sensor Necessary preliminary tasks: Remove trim panel for pedal assembly. Release screw (1). Detach heating duct in rear compartment on left ... . Installation: Make sure heating duct in rear compartment on left (2) is correctly seated. Unfasten plug connection (1) and disconnect. Pull out evaporator temperature sensor (2) in direction ...

Functional Description (FUB) Outside temperature sensor

Ambient temperature sensor Outside temperature sensor The ambient temperature sensor is not directly linked to the engine control unit but to the instrument cluster. The value of the ambient temperature is sent to the engine control unit via CAN bus. In the event of a fault, the instrument cluster sends a characteristic value which the DME interprets as a fault ...

Repair Instructions (REP) Replacing sensor fan for interior temperature

64 11 902 Replacing sensor fan for interior temperature Necessary preliminary tasks: Remove control panel for heater - A/C system. Release screws (1). Pull out sensor blower for interior temperature (2) in direction of arrow. Installation: Make sure pins (3) are correctly seated in base (4). ...

Functional Description (FUB) Locating plate

Notes on the diagnosis system Locating plate Testing instructions for dual mass flywheel Repair instructions: Removing starter motor Through the gearbox opening, check whether one locating plate or both locating plates has / have come loose on the primary side of the dual mass flywheel and landed in the transmission housing (see graphic) Illustration: Index ...

Repair Instructions (REP) Replacing temperature sensor for cold-air distributor

64 11 916 Replacing temperature sensor for cold-air distributor Necessary preliminary tasks: Remove audio system controller / remove Car Communication Computer Disconnect plug connection (2). Important! Do not bend temperature sensor for cold-air distributor (1). Turn temperature sensor for cold-air distributor (1) counterclockwise, feed out towards bottom and remove ...

Repair Instructions (REP) Removing and installing/replacing outside temperature sensor

65 81 060 Removing and installing/replacing outside temperature sensor Necessary preliminary tasks: Remove front underbody protection Unfasten plug connection (1) and disconnect. Unclip outside temperature sensor (2) in direction of arrow from panel (3) and remove. Installation: Make sure outside temperature sensor (2) is correctly engaged. ...

Repair Instructions (REP) Replacing coolant temperature sensor (N62, N62TU)

13 62 531 Replacing coolant temperature sensor (N62, N62TU) Warning! Danger of scalding! Only perform these tasks on an engine that has cooled down. Necessary preliminary tasks: Read ... . Observe country-specific waste-disposal regulations. Coolant temperature sensor is mounted on water pipe at front. Unlock plug (1) and remove. Release temperature sensor (2 ...

Functional Description (FUB) Intake air temperature sensor

Functional description Intake air temperature sensor The intake air temperature sensor is integrated in the air mass flow meter. In this way, the intake air temperature is measured ... control adaptation - Idle control - VANOS activation - Valvetronic control - Activation of secondary air system - Activation of electric fan If a fault occurs on the temperature sensor ...

Repair Instructions (REP) Removing and installing/replacing temperature sensor for heating unit

64 11 912 Removing and installing/replacing temperature sensor for heating unit Necessary preliminary tasks: Remove on-board monitor. Unlock plug connection (1) on left/right and disconnect. Pull out temperature sensor for heating unit in direction of arrow out of heating unit (2). Installation: Make sure temperature sensor for heating unit is correctly seated. ...

Functional Description (FUB) Coolant Temperature Sensor at Radiator Outlet

Coolant Temperature Sensor at Radiator Outlet This temperature sensor is fitted in the heater return hose of the radiator and it registers the coolant temperature after it flows out of the radiator. The coolant temperature at the radiator outlet serves the purpose of driving the electric fan. ...

Repair Instructions (REP) in the installation location

11 . . . . . Equipment recoding special tool number of the transverse member for fixing the engine in the installation location Equipment recoding from 00 0 200 to 00 6 0 000 Designation Special tool new Special tool previous Cross-member, previous --- 00 0 200 Cross-member, new 00 6 000 --- Mounting bridge 00 6 001 00 0 201 Spindle with hook 00 6 002 00 0 202 ...

Wiring Diagram (SSP) Temperature control
Applies to: ihkah -2005/02

... air temperature sensor 31 TEMP_FRI 0.5 BL 31_SENS 0.5 BR 1 X10591 2 . B97 Coolant pressure sen- sor 9 31 DSA DSENS-- 0.5 0.5 BL/SW BR/BL 31 8 X10591 3 SENS+ 0.5 GR/SW 15(5V) FSCHI+ 0.5 ... Temperature control X13783 X85 1 31 0.5 BR WVLI WVRE 0.5 0.5 GE/BR GE/VI 3 X85 2 . A11a Heating/air condition- ing system . A11a Heating/air condition- ing system 2 X772 1 . B11a ...

Wiring Diagram (SSP) Temperature control
Applies to: ihkah 2005/03 - 2007/02

... temperature sensor 31 TEMP_FRI 0.5 BL 31 0.5 BR 1 X10591 2 . B97 Coolant pressure sen- sor 9 31 DSA DSENS-- 0.5 0.5 BL/SW BR/BL 31 8 X10591 3 SENS+ 0.5 GR/SW 15(5V) FSCHI+ 0.5 WS/GN 1 X981 15(5V ... Temperature control X85 1 31 0.5 BR WVLI WVRE 0.5 0.5 GE/BR GE/VI 3 X85 2 . A11a Heating/air condition- ing system . A11a Heating/air condition- ing system 2 X772 1 . B11a Heating heat ...

Wiring Diagram (SSP) Temperature control
Applies to: ihkah 2007/03+

... Heating heat exchan- ger temperature sen- sor, right 31 FUE-- 0.5 BR/SW TFR 0.5 GE/VI 2 X771 1 31 FUE-- 0.5 BR/SW VF 0.5 GR 1 X13729 3 . B13729 Fresh air temperature sensor 31 TEMP_FRI ... Temperature control X85 1 31 0.5 BR WVLI WVRE 0.5 0.5 GE/BR GE/VI 3 X85 2 . A11a Heating/air condition- ing system . A11a Heating/air condition- ing system 2 X772 1 . B11a Heating heat ...

Wiring Diagram (SSP) Temperature control
Applies to: ihkab 2005/03 - 2007/02

Temperature control 31 31 15 TF 0.5 GE/RT 1 FUE-- 0.5 BR/SW X01141 2 . B11b Heating heat exchan- ger temperature sen- sor 1 31 . A11a Heating/air condition- ing system 31 FUE-- 0.5 BR ... sensor VTF 0.5 GR 31 DSENS+ 0.5 GR/SW X18793 4 DSENS-- 0.5 BR/BL 1 X10591 2 . B97 Coolant pressure sen- sor DSA 0.5 BL/SW 8 X10591 3 . A11a S_KOMP 0.75 SW/GR Heating/air condition- ing ...

Wiring Diagram (SSP) Temperature control
Applies to: ihkab 2007/03+

Temperature control 31 31 15 TF 0.5 GE/RT 1 FUE-- 0.5 BR/SW X01141 2 . B11b Heating heat exchan- ger temperature sen- sor 1 31 . A11a Heating/air condition- ing system 31 FUE-- 0.5 BR ... sensor VTF 0.5 GR 31 DSENS+ 0.5 GR/SW X18793 4 DSENS-- 0.5 BR/BL 1 X10591 2 . B97 Coolant pressure sen- sor DSA 0.5 BL/SW 8 X10591 3 . A11a S_KOMP 0.75 SW/GR Heating/air condition- ing ...

Wiring Diagram (SSP) Temperature control
Applies to: ihkab -2005/02

Temperature control 31 31 15 TF 0.5 GE/RT 1 FUE-- 0.5 BR/SW X01141 2 . B11b Heating heat exchan- ger temperature sen- sor 1 31 . A11a Heating/air condition- ing system 31 FUE-- 0.5 BR ... tempera- ture sensor VTF 0.5 GR 31 DSENS+ 0.5 GR/SW X18793 4 DSENS-- 0.5 BR/BL 1 X10591 2 . B97 Coolant pressure sen- sor DSA 0.5 BL/SW 8 X10591 3 . A11a S_KOMP 0.75 SW/GR Heating ...

Repair Instructions (REP) Notes on using temperature-controlled infra-red radiators

... drying spatula and filler. The temperature sensors in the infrared radiator only operate reliably on large, even surfaces. On small surfaces such as C-pillars or sills, often only ... the drying process with an external temperature sensor. The general rule is: The surface temperatures must not exceed 85°C. Important! Do not use infrared radiators on carbon parts! Risk ...

Repair Instructions (REP) Overview, rain sensor (additional work when replacing the windscreen / sensor replacement)

... required RLPSS (Rain, light and precipitation solar sensor) (Designation is located on the back of the sensor) approximately ø 50 mm Yes Yes - Yes Yes RLS (vehicle with no HUD) (Designation is located on the back of the sensor) approximately ø 50 mm No (new substitute visuals required, refer to Electronic Parts Catalogue) - No Yes Yes RLSS (vehicle with HUD ...

Repair Instructions (REP) Replacing fogging sensor

64 11 970 Replacing fogging sensor 00 9 317 Warning! Make sure rooms are well ventilated when working with adhesive remover indoors. Important! Do not under any circumstances use paint ... connection (1). Note: If necessary, carefully heat fogging sensor (2) with a hot air blower to approx. 40-60 °C. Lift off fogging sensor (2) with special tool 00 9 317 and slowly pull off ...

Repair Instructions (REP) Adjusting ACC sensor

66 31 001 Adjusting ACC sensor 36 1 100 66 3 150 Unclip trim (1) at points (2) and remove in direction of arrow from bumper trim (3). Installation: Make sure trim (1) is correctly seated. Locking hooks (2) and retaining element (3) must not be damaged. Carry out adjustment of ACC sensor (1) with special tool 66 3 150 by means of adjusting screws (2). Special tool ...

Repair Instructions (REP) Adjusting ACC sensor

66 31 001 Adjusting ACC sensor 36 1 100 36 1 130 Important! Check ease of movement of adjustment screws prior to adjustment. Pull-off torque of adjustment screws must not exceed 4 Nm ... -off torque is greater than 4 Nm, observe instructions on replacing adjustment screws. Lever out cap (1). Carry out adjustment of ACC sensor (2) with special tool 36 1 130 by means ...

Repair Instructions (REP) Replacing a brake pad sensor

34 35 001 Replacing a brake pad sensor Necessary preliminary tasks: Remove wheel Important! The brake pad wear sensor must be replaced once it has been removed (brake pad wear sensor loses its retention capability in the brake pad). If a brake pad sensor that has already been ground has to be replaced even though the minimum brake pad thickness has not yet been ...

Repair Instructions (REP) Removing and installing/replacing fuel gauge sensor (complete right sensor unit)

16 12 000 Removing and installing/replacing fuel gauge sensor (complete right sensor unit) 16 1 020 Important! Ensure adequate ventilation in the place of work! Ensure absolute ... completely from fuel tank Remove rear seat Remove left sensor unit Fold carpet (1) forwards. Detach insulating mat (2) above left and right sensor units at perforation and fold back ...

Repair Instructions (REP) Removing and installing (replacing) long range sensor (LRR sensor) (M-kit)
Applies to: 2007/03+

66 31 016 Removing and installing (replacing) long range sensor (LRR sensor) (M-kit) 00 9 317 Tape off bumper in working area (1) with yellow plastic adhesive tape. Lever out trim with special tool  00 9 317  and remove. Firmly press down plastic adhesive tape (1) in working area again. Unclip long range sensor (2) from mounting. Installation: Make sure long range ...

Repair Instructions (REP) Removing and installing/replacing fuel gauge sensor (complete left sensor unit)

16 12 001 Removing and installing/replacing fuel gauge sensor (complete left sensor unit) 16 1 020 Important! Ensure adequate ventilation in the place of work! Ensure absolute ...  020. Installation: Replace rubber gasket. Tightening torque 16 14 2AZ. Important! Risk of breakage! Carefully raise fuel level sensor until sensor flange projects out of tank opening ...

Repair Instructions (REP) Replacing screws on ACC sensor unit

66 31 ... Replacing screws on ACC sensor unit Necessary preliminary tasks: Remove ACC sensor Important! Perform a visual inspection of the sensor housing for damage/leaks. If damaged, replace the ACC sensor housing! Clamp sensor housing (1) on screw in vice (2). Release the screw by twisting the sensor housing (2). Important! After releasing the screws, check ...

Repair Instructions (REP) Removing and installing/replacing differential pressure sensor (N62, N62TU)

... . Unlock and disconnect following plug connections. Fuel rail, left and right, on cable duct Throttle-valve assembly Knock sensor, left and right All solenoid valves Both temperature sensors Oil-pressure switch Tank venting valve Alternator Valvetronic servomotor, left and right Pulse generator on exhaust and inlet camshafts, left and right Eccentric shaft sensor, left ...

Repair Instructions (REP) Removing and installing (replacing) ACC sensor

66 31 006 Removing and installing (replacing) ACC sensor 00 9 317 Unclip cover (1) at points (2) and remove in direction of arrow from bumper panel (3). Important! To prevent damage to bumper panel when feeding out the ACC sensor, cover area around bumper recess with suitable adhesive tape. Installation note: Make sure cover (1) is correctly seated. Locking hooks (2 ...

Repair Instructions (REP) Removing and installing / replacing DSC sensor
Applies to: 1998/09+

... tasks: Remove right front seat Remove front inside entrance cover strip Lift carpet and fold back to one side Note: The yaw sensor comprises the function of the transversal-acceleration sensor and the yaw sensor. Unlock plug connection. Installation: Make sure plug connection locks correctly. Release screws (1) and remove rotation rate sensor. Installation: Tightening ...

Repair Instructions (REP) Initializing rain/light (solar) sensor

61 35 679 Initializing rain/light (solar) sensor Note: Initialization is necessary: after replacing windscreen after replacing rain/light (solar) sensor after replacing optical element on rain/light (solar) sensor after installing a used rain/light (solar) sensor Note: Connect BMW diagnosis system Initializing rain/light (solar) sensor ...

Repair Instructions (REP) Replacing front ride-height sensor

37 14 511 Replacing front ride-height sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Note: Build date up to 03/04: Variant (A) - connection (1) points downwards Build date from 03/04: Variant (B) - connection (2) points upwards Build date up to 03/2004: Important! If the front ride-height sensor has been ...

Repair Instructions (REP) Replacing rear ride-height sensor

37 14 512 Replacing rear ride-height sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Release nut and disconnect jointed rod (3). Installation: Replace self-locking nut. Tightening torque 37 14 7AZ. Release screws (1). Tightening torque 37 14 6AZ. Disconnect plug connection (4) and remove ride-height sensor ...

Repair Instructions (REP) Removing and installing/replacing solar sensor

64 11 992 Removing and installing/replacing solar sensor Necessary preliminary tasks: Remove speaker frame from trim for instrument panel at top. Unlock catches (1) in direction of arrow and remove solar sensor (2) from speaker frame (3). Installation: Catches (1) on speaker frame (3) must not be damaged. Make sure solar sensor (2) is correctly seated in speaker ...

Repair Instructions (REP) Information on intelligent battery sensor (IBS)

61 12 ... Information on intelligent battery sensor (IBS) Notice! Do not connect the charger to the 12 V charging socket The 12 V charging socket is supplied with voltage by the rear ... connection between the IBS and the sensor screw. Do not use force when disconnecting the pole shoe from the battery terminal: Do not pull on the ground cable. Do not place any tools under ...

Repair Instructions (REP) Replacing pressure sensor GS6S53BZ (SMG)
Applies to: MANUAL

23 42 508 Replacing pressure sensor GS6S53BZ (SMG) Important! Before working on hydraulic system: Reduce pressure in hydraulic system by means of Service Function in DIS Tester ... protective plate. Tightening torque 23 41 7AZ. Disconnect plug and release pressure sensor (2). Tightening torque 23 41 10AZ. Installation: Replace sealing ring. Note: After completing ...

Repair Instructions (REP) Removing and installing/replacing inside mirror (with rain sensor)

51 16 060 Removing and installing/replacing inside mirror (with rain sensor) Important! Work may only be carried out at a room/object temperature of 18 ... 28 °C. If this can not be guaranteed (cold/hot countries), it is necessary to equalise the temperature of the windscreen, mirror base and inside mirror (e.g. vehicle left to stand indoors or in the shade ...

Repair Instructions (REP) Replacing shift and/or selector sensor GS6S53BZ (SMG)
Applies to: MANUAL

23 42 542 Replacing shift and/or selector sensor GS6S53BZ (SMG) Note: After completing work: Perform ”Teach in transmission” service function by means of DIS Tester Necessary preliminary tasks: Remove SMG transmission Important! Shift and selector sensors can only be removed/installed when transmission is set to ”N”. Removing shift sensor: Unfasten screws. Tightening ...

Repair Instructions (REP) Carrying out steering angle sensor adjustment

61 31 996 Carrying out steering angle sensor adjustment Important! In vehicles with active steering, steering angle sensor adjustment is integrated in the service function ”Initial operation/adjustment for active steering” and must not be carried out separately! Note: Steering angle sensor adjustment must be carried out: Before adjustment work on the front axle ...

Repair Instructions (REP) Removing and installing (replacing) rain/light sensor

61 35 177 Removing and installing (replacing) rain/light sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Necessary preliminary ... : Catches of two-part mirror base cover (1) must not be damaged or missing. Disconnect plug connection (3). Release locks (1) in direction of arrow and remove rain/light sensor (2) from ...

Repair Instructions (REP) Removing and installing/replacing steering angle sensor

32 31 082 Removing and installing/replacing steering angle sensor Note: Steering angle sensor is integrated in the steering column stalk fixture. After installation: Replacement only: Carry out programming/coding Carry out steering angle sensor adjustment/adjustment for active front steering ...

Repair Instructions (REP) Replacing left knock sensors (N62, N62TU)

12 14 611 Replacing left knock sensors (N62, N62TU) (cylinder bank 5 to 8) Necessary preliminary tasks: Read out fault memory of DME control unit Check stored fault messages Switch off ignition Remove intake air manifold Important! Mixing up the knock sensor plug connections will result in engine damage! Routing of wires and plug connections must conform ...

Repair Instructions (REP) Replacing right knock sensors (N62, N62TU)

12 14 610 Replacing right knock sensors (N62, N62TU) (cylinder bank 1 to 4) Necessary preliminary tasks: Read out fault memory of DME control unit Check stored fault messages Switch off ignition Remove intake air manifold Important! Mixing up the knock sensor plug connections will result in engine damage! Routing of wires and plug connections must conform ...

Repair Instructions (REP) Removing and installing (replacing) left or right short range sensor (SRR sensor) (M Technik
Applies to: 2007/03+

66 31 020 Removing and installing (replacing) left or right short range sensor (SRR sensor) (M Technik aerodynamic kit) Important! To ensure correct SRR operation, there must ... : Remove front bumper trim Remove impact absorber (1) and carefully detach adhesive tape in area (2). Drill out riveted joints (1) and remove bracket (2) for SRR sensor. Disconnect ...

Repair Instructions (REP) Removing and installing (replacing) vehicle centre sensor

65 77 730 Removing and installing (replacing) vehicle centre sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Warning! Note ... armrest. Disconnect Bowden cable (1). Installation: Make sure Bowden cable is correctly guided. Release screws (1). Disconnect plug connections (2) and remove vehicle centre sensor (3 ...

Repair Instructions (REP) Removing and installing / replacing lateral acceleration sensor
Applies to: 1998/09+

37 14 610 Removing and installing / replacing lateral acceleration sensor Important! Read and comply with notes on protection against damage from electrostatic discharge (ESD protection) . Important! Do not kink floor trim panel under any circumstances! Necessary preliminary tasks: Remove right front seat Lift floor trim panel and fold back to one side Release screws ...

Functional Description (FUB) Camshaft sensor

Camshaft sensor The camshaft sensor registers the position of the camshaft with the aid of a sheet metal wheel with various apertures screwed to the camshaft. It operates in accordance with the Hall effect principle. Hall effect A permanent magnet in the sensor produces a magnetic field. A conductor with current flowing through it is located in this magnetic field ...

Functional Description (FUB) Crankshaft sensor

... point). Function A permanent magnet in the sensor produces a magnetic field. A conductor with current flowing through it is located in this magnetic field. An electric voltage dependent ... Crankshaft sensor The crankshaft sensor registers the position of the crankshaft with the aid of a sheet metal wheel with various apertures screwed to the crankshaft. It operates ...

Repair Instructions (REP) Replacing left oxygen monitor sensor (N62 / N62TU)

11 78 540 Replacing left oxygen monitor sensor (N62 / N62TU) 11 7 030 (cylinder bank 5 to 8) Necessary preliminary tasks: Switch off ignition. Remove rear underbody protection Warning! Scalding hazard! Only perform this task on an engine that has cooled down. Unlock and detach plug connection (1) for monitor sensor (2). Unclip monitor sensor cable. Release monitor ...

Repair Instructions (REP) Replacing right oxygen monitor sensor (N62/N62TU)

11 78 543 Replacing right oxygen monitor sensor (N62/N62TU) 11 7 030 (cylinder bank 1 to 4) Necessary preliminary tasks: Switch off ignition Remove rear underbody protection Warning! Scalding hazard! Only perform this task on an engine that has cooled down. Unlock and detach plug connection (1) for monitor sensor (2). Unclip monitor sensor cable. Release monitor ...

Functional Description (FUB) Rain/light solar sensor
Applies to: rlss70

... photosensors that pick up the brightness of the ambient light and of the frontal light. On the E70, the front light sensor regulates the brightness of the Head-Up Display. Solar sensor ... , rather the gel is destroyed. Index Explanation Index Explanation 1 Cover for mirror base 2 Condensation sensor 3 Rain/light solar sensor This installation location ensures ...

Repair Instructions (REP) Replacing right oxygen control sensor (N62/N62TU)

11 78 533 Replacing right oxygen control sensor (N62/N62TU) 11 7 030 (cylinder bank 1 to 4) Necessary preliminary tasks: Switch off ignition. Remove reinforcement plate Warning! Scalding hazard! Only perform this task on an engine that has cooled down. Release plug connector (1) and pull off. Unclip control sensor cable. Release control sensor (2) with special tool ...

Repair Instructions (REP) Replacing left oxygen control sensor (N62/N62TU)

11 78 530 Replacing left oxygen control sensor (N62/N62TU) 11 7 030 11 9 150 (cylinder bank 5 to 8) Necessary preliminary work: Switch off ignition. Remove reinforcement plate. Remove front propeller shaft (E7X only). Warning! Risk of burning! Only perform this task on an engine that has cooled down. Unlock plug connector (3) and pull off. Unclip control sensor cable ...

Functional Description (FUB) Intelligent battery sensor and battery

... and the temperature of the battery. The following components are fitted in the electronics module: a precision resistor (resistor for current measurement) a temperature sensor evaluation electronics ... : Average ambient temperature with vehicle parked. Ambient temperature of the last journey. Current state of charge. Voltage dip of the last engine start (trend for ageing of the battery ...

Repair Instructions (REP) Removing and installing (replacing) left B-pillar sensor

65 77 720 Removing and installing (replacing) left B-pillar sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Warning! Note ... -pillar sensor (3) slightly through opening in B-pillar and feed out towards rear. If necessary, unclip cable duct (4). Unlock plug connections (1) and disconnect. Remove B-pillar sensor ...

Repair Instructions (REP) Removing and installing (replacing) left front door sensor

65 77 740 Removing and installing (replacing) left front door sensor Warning! Note airbag safety instructions! Incorrect handling can activate airbag and cause injury. Important! Read ...  (1) and remove front door sensor (2) from door. Disconnect plug connection (3). Installation: Make sure rubber ring and sensor are securely seated. Tightening torque 65 77 7AZ. ...

Repair Instructions (REP) Removing and installing/replacing front pressure sensor for DSC

34 52 575 Removing and installing/replacing front pressure sensor for DSC Necessary preliminary tasks: Remove front right wheel arch panel Read and comply with General Information ... . This prevents brake fluid from emerging from the expansion tank and air from entering the system when the brake lines are opened. Unlock plug connection (1). Release pressure sensor ...

Repair Instructions (REP) Removing and installing/replacing rear pressure sensor for DSC

34 52 580 Removing and installing/replacing rear pressure sensor for DSC Note: Read and comply with General Information. After completing work: Bleed braking system Press brake pedal ... is correctly seated. Replace heat protection as needed. Disconnect plug connection (1). Release pressure sensor (2) and remove. Installation note: Tightening torque 34 51 12AZ. ...

Repair Instructions (REP) Replacing sensor mat for passenger seat occupancy detector

65 77 600 Replacing sensor mat for passenger seat occupancy detector This job is described under: ”Replacing seat cover for left or right front seat”. ...

Repair Instructions (REP) Removing and installing/replacing sensor for automatic recirculated air control

64 11 991 Removing and installing/replacing sensor for automatic recirculated air control Unfasten plug connection (1) and disconnect. Feed out sensor for automatic recirculated air control (2) in direction of arrow and remove. Installation: Make sure sensor for automatic recirculated air control (2) is correctly seated. ...

Repair Instructions (REP) Removing and installing/replacing front left or right acceleration sensor

65 77 541 Removing and installing/replacing front left or right acceleration sensor Note: Acceleration sensor only fitted in US version! Necessary preliminary tasks: Remove front bumper trim Disconnect plug connection (1). Release screws (2) and remove acceleration sensor (3). Installation: Tightening torque 65 77 9AZ. Replace screws (2). ...

Repair Instructions (REP) Removing and installing/replacing yaw sensor for active front steering

32 43 515 Removing and installing/replacing yaw sensor for active front steering Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Important! Do not kink floor panelling under any circumstances! Necessary preliminary tasks: Remove left front seat Raise rear left floor trim in area of center console Release screws (1 ...

Repair Instructions (REP) Removing and installing/replacing emergency power siren with tilt sensor

65 75 557 Removing and installing/replacing emergency power siren with tilt sensor Important! Read and comply with notes on protection against electrostatic damage (ESD protection). Necessary preliminary tasks: Remove rear right bumper bracket Unscrew nut (1). Remove emergency power siren cover (2) from bumper bracket (3). Disconnect plug connection (1). Remove ...

Functional Description (FUB) Oil condition sensor

... measures the following variables: Engine oil temperature Oil level Engine oil quality The engine control system evaluates these measurements. With the oil condition sensor, the electrical ... have an electronic oil level check. Item Explanation Item Explanation 1 Oil sump 2 Oil condition sensor 3 Temperature sensor 4 three‐pin plug connection The oil condition sensor ...

Wiring Diagram (SSP) Sensor system
Applies to: dsc_60, dsc_87, dsc_e65 -2005/08

Sensor system SP0000019399C1026Sensor system B2 Front left wheel speed sensor 1 X114 2 RT 0.5 DS_VL BL/RT 0.5 DP_VL B1 Front right wheel speed sensor 1 X113 2 GE 0.5 DS_VR BL/GE 0.5 DP_VR 1 X377 2 GN 0.5 DS_HR BL/GN 0.5 DP_HR B4 Rear left wheel speed sensor 1 X376 2 WS 0.5 DS_HL BL/WS 0.5 DP_HL B16a Brake pad wear sensor, frontleft 1 X18145 2 GE 0.35 BBSV B17a Brake ...

Functional Description (FUB) Rain/rain/light sensor
Applies to: rls_87, rls_ds2, rls_e65

Description of operation Rain/rain/light sensor The rain/light sensor has integrated sensors that sense the wetness on the windscreen glass and the ambient brightness. Rain sensor ... and light striking the sensor from above (ambient light) are sensed. The prerequisites for trouble-free operation of the driving light sensor are those of the rain sensor ...

Wiring Diagram (SSP) Sensor system
Applies to: 2007/03+

Sensor system SP0000025764C1026Sensor system B4 Rear left wheel speed sensor B75 Rotation rate sensor B3 Rear right wheel speed sensor B2 Front left wheel speed sensor B1 Front right wheel speed sensor A149a Car access system 31 B16a Brake pad wear sensor, frontleft B17a Brake pad wear sensor, rearright A65a Dynamic stability control (DSC) 15 31 15 31 15 31 15 31 15 ...

Wiring Diagram (SSP) Sensor system
Applies to: dsc_60, dsc_87, dsc_e65 2005/09+

Sensor system DGR_5V 0.35 GE/RT X1746 9 X14033 3 32 15_SENSO 0.35 GN/GE X1653 4 2 F_CAN_L 0.5 WS X1653 3 F_CAN_H 0.5 BL/WS 26 14 31E 0.35 BR/SW 1 2 31<DSC 0.35 BR/WS DGR_1 0.35 GR ... sensor, front axle . B114a Brake pressure sensor, rear axle DGR_5V DGR_5V 0.35 0.35 GE/RT GE/RT X14049 31<DSC 0.35 BR/WS DGR_2 0.35 GE X14049 31 31 . A65a Dynamic stability control (DSC ...

Wiring Diagram (SSP) Airbag sensors
Applies to: LHD 2007/09+

Airbag sensors SP0000055812C1016Airbag sensors A173a Airbag sensor, B-pillar, driver'sside BR/GE 0.35 SSBBSFY+ OR 0.35 SSBBSFY- GR/GN 0.35 SSBBSFX- GR/WS 0.35 SSBBSFX+ 2 3 4 X10335 1 B78a Airbag sensor, front driver'sside door GR/BR 0.5 SSTF+ GR/SW 0.5 SSTF- GR/BR 0.5 SSTF+ GR/SW 0.5 SSTF- 15 X257 14 1 X1886 2 BL/WS 0.5 GKF BR 0.5 31 BL/WS 0.5 GKF SW/RT 0.35 ...

Wiring Diagram (SSP) Sensor system
Applies to: dxc8_p 2005/09+

Sensor system 32 15_SENSO 0.35 GN/GE X1653 4 2 F_CAN_L 0.5 WS X1653 3 F_CAN_H 0.5 BL/WS 26 14 31E 0.35 BR/SW 1 X13786 15 31 31 . B75 Rotation rate sen- sor . A65a Dynamic stability control (DSC) . A65a Dynamic stability control (DSC) 1 X114 2 DS_VL DP_VL 0.5 0.5 RT BL/RT 22 21 . B2 Front left wheel speed sensor 1 X113 2 DS_VR DP_VR 0.5 0.5 GE BL/GE 6 18 . B1 Front ...

Wiring Diagram (SSP) Sensor system

Sensor system GR/BR 0.5 S_CLTPOS 2 BR 0.5 SNSGND2 1 . Clutch position sensor 15 4 31 RT/WS 0.5 5V_2 2 15(5V) 3 31 WS/GE 0.5 A_GEARPO 2 BR 0.5 SNSGND1 3 . Gearshift sensor 16 12 31 . Sequential manual transmission (SMG) RT/WS 0.5 5V_1 11 15(5V) 1 31 3 GN/WS 0.5 A_SHFPOS 2 . Selector angle sensor 3 31 RT/WS 0.5 5V_1 1 SNSGND1 BR 0.5 GE 0.5 F_DZGN+ 1 SW 0.5 F_DZGN-- 2 ...

Wiring Diagram (SSP) Airbag sensors
Applies to: RHD 2007/09+

Airbag sensors SP0000055813C1016Airbag sensors A174a Airbag sensor, B-pillar, passen-ger's side BR/GE 0.35 SSBBSFY+ OR 0.35 SSBBSFY- GR/GN 0.35 SSBBSFX- GR/WS 0.35 SSBBSFX+ 2 3 4 X10335 1 B78a Airbag sensor, front driver'sside door BL/BR 0.5 SSTF+ BL/RT 0.5 SSTF- GR/BR 0.5 SSTF+ GR/SW 0.5 SSTF- 15 X257 14 1 X1886 2 GE/BR 0.5 GKBF BR 0.5 31 GE/BR 0.5 GKBF SW ...

Wiring Diagram (SSP) Sensor system
Applies to: dxc8_p -2005/08

Sensor system 32 15_SENSO 0.35 GN/GE X1653 4 2 F_CAN_L 0.5 WS X1653 3 F_CAN_H 0.5 BL/WS 26 14 31E 0.35 BR/SW 1 X13786 15 31 31 . B75 Rotation rate sensor . A65a Dynamic stability con- trol (DSC) . A65a Dynamic stability con- trol (DSC) 1 X114 2 DS_VL DP_VL 0.5 0.5 RT BL/RT 22 21 . B2 Front left wheel speed sensor 1 X113 2 DS_VR DP_VR 0.5 0.5 GE BL/GE 6 18 . B1 Front ...

Repair Instructions (REP) Removing and installing/replacing air-mass flow sensor (N62, N62TU)

13 62 560 Removing and installing/replacing air-mass flow sensor (N62, N62TU) Necessary preliminary tasks: Read out fault memory of DME control unit; if necessary, work through test ... air-mass flow sensor and air intake hose for damage, replacing if necessary. Unfasten screws. Pull air-mass flow sensor (1) out of upper section of intake filter housing. Note: Check ...

Wiring Diagram (SSP) Crankshaft sensor
Applies to: 2005/09+

Crankshaft sensor SP0000024307 C13 Crankshaft sensor A6009 Integrated supply module (IVM) 87 F005 30A X60093 13 OR 0.5 KL.87 X6203 1 B6203 Crankshaft sensor 3 X6203 2 GE 0.5 P_KWG SW 0.5 M_DIGIT X6450 27 X60003 37 A6000 DME control unit 31 31 ...

Wiring Diagram (SSP) Airbag sensors
Applies to: RHD -2007/08

Airbag sensors SSBBSFX+ 0.35 BL/BR SSBBSFX-- 0.35 BL/RT 13 3 3 SSBBSFY+ 0.35 BL/BR 14 2 SSBBSFY-- 0.35 BL/RT X10335 1 4 . A174a Airbag sensor, B- pillar, passenger's side X1886 2 . B78a SSTF+ SSTF-- 0.5 0.5 BL/BR BL/RT Airbag sensor, front driver's side door X257 14 15 1 4 12 2 X10179 24 X18165 2 . S59a GKBF 31 0.5 0.5 GE/BR BR Passenger's seat belt ...

Wiring Diagram (SSP) Airbag sensors
Applies to: LHD -2007/08

Airbag sensors SSBBSFX+ 0.35 BL/BR SSBBSFX-- 0.35 BL/RT 13 3 3 SSBBSFY+ 0.35 BL/BR 14 2 SSBBSFY-- 0.35 BL/RT X10335 1 4 . A173a Airbag sensor, B- pillar, driver's side X1886 2 . B78a SSTF+ SSTF-- 0.5 0.5 BL/BR BL/RT Airbag sensor, front driver's side door X257 14 15 1 4 12 2 15 X18165 2 . S58a GKF 31 0.5 0.5 BL/WS BR Driver's seat belt buckle contact 1 ...

Repair Instructions (REP) Removing and installing/replacing right eccentric shaft sensor (N62/N62TU)

11 37 040 Removing and installing/replacing right eccentric shaft sensor (N62/N62TU) (cylinder bank 1 to 4) Necessary preliminary tasks: Remove right cylinder head cover Unfasten screws. Remove eccentric shaft sensor (1). Installation: Read out fault memory of control unit of Digital Motor Electronics (DME). Check stored fault messages. Rectify faults. Now clear ...

Can't find what you're looking for? Keep the following in mind for better results:
  • This site is a translation of the original German documentation into international English, and therefore things may be called differently from what you're used to in your dialect (think for example: subframe vs. axle carrier, bushing vs. rubber mount, differential vs. final drive, sway bar vs. anti-roll bar, and so forth)
  • There may not be a writeup specifically on "replacing subframe bushes", because it is incorporated into a larger one for "removing the axle carrier". Try broadening the scope if your search comes up empty.
  • When there are too many matches, only the most relevant results are displayed.
Sponsored links